Side-Power SX80/185T Instrukcja Instalacji Pobierz pdf (Strona 3)

Installation

To achieve maximum effect, reliability and durability from your Sidepower Sternthruster, a correct installation is very

important.

Please follow the instructions carefully, and make sure that all checkpoints are carefully controlled.

1. Make sure that there are enough space both inside and outside the transom of the boat (see FIG 1).

Outside of flange:

Cut out in stern:

Bolt holes dia :

Bolt postion radius :

60°

PS !

Necessary

support

of motor.

Minimum is

hulls bottom

thickness

W.L.

FIG. 1

Stern thruster installation manual Version 1.6 - 2005

Additional considerations for positioning of stern thruster.

 Make sure that the stern-tunnel does not disturb the waterflow under the hull

 Ensure that when installed the thruster does not foul exisiting equipment inside the boat like steerage links etc.

 It is essential that the motor is supported so that the total weight is not on the tunnel alone.

 Make sure that the water flow from the thruster are not intereferred to much by sterndrives, trimtabs etc. as this

will reduce the thrust considerably.

 It is possible to mount the tunnel off the boat’s centre line if necessary.

 If the stern thickness is to much for the thruster in question you can easily remove material in the necessary area

to fit the thruster. The stern thickness even here will never have to be less than the max. measurement given as

max. stern thickness.

Measurements ref.

mm / inch

SP30Si / SP40Si SP55Si SP75Ti SP95Ti SP125Ti SP155TCi SP200TCi

SP200TCi-32 /

SP240TCi

SP285TCi

A 200mm / 7,87'' 225mm / 8,90" 312mm / 12,30" 349mm / 13,70" 363mm / 15,10" 386mm / 15,20" 419mm / 16,50" 440mm / 17,30" 404mm / 15,90"

B 190mm / 7,48'' 256mm / 10,08" 256mm / 10,08" 256mm / 10,08" 340mm / 13,39" 340mm / 13,39" 360mm / 14,20" 420mm / 16,54" 420mm / 16,54"

C 135mm / 5,31'' 150mm /5,91" 200mm / 7,87" 200mm / 7,87" 250mm / 9,84" 250mm / 9,84" 300mm / 11,81" 300mm / 11,81" 300mm / 11,81"

D 197mm / 7,76'' 337mm / 13,30" 337mm / 13,30" 337mm / 13,30" 350mm / 13,80" 350mm / 13,80" 350mm / 13,80" 456mm / 18,00" 456mm / 18,00"

E ø217mm / 8,54'' ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" ø300mm / 11,80" 356mm / 14,02" ø396mm / 15,60" ø396mm / 15,60"

F ø160mm / 6,30'' ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø200mm / 7,84" ø260mm / 11,24" ø265mm / 10,40" ø265mm / 10,40"

G 6 x ø6,5mm / 0,26'' 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 8x ø10,5mm / 0,41"

H ø98mm / 3,86'' ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø129mm / 5,08" ø315mm / 12,40" ø345,6mm / 13,60" ø345,6mm / 13,60"

Max. Stern

thickness

14mm / 0,55'' 35mm / 1,38" 54mm / 2,13" 54mm / 2,13" 60mm / 2,36" 60mm / 2,36" 50mm / 1,97" 60mm / 2,36" 60mm / 2,36"

Measurements ref.

mm / inch

SP100HYD SP220HYD SP300HYD SP550HYD

A 158mm / 6,22" 178mm / 7,01" 208mm / 8,19" 259mm / 10,20"

B 256mm / 10,08" 340mm / 13,39" 420mm / 16,54" 570mm / 22,44"

C 200mm / 7,87" 300mm / 11,81" 300mm / 11,81" 380mm / 14,96"

D 337mm / 13,30" 350mm / 13,80" 456mm / 18,00" 550mm / 21,65"

E ø300mm / 11,80" ø300mm / 11,80" ø396mm / 15,60" ø600mm / 23,62"

F ø200mm / 7,84" ø200mm / 7,84" ø265mm / 10,40" ø400mm / 15,75"

G 6x ø10,5mm / 0,41" 6x ø10,5mm / 0,41" 8x ø10,5mm / 0,41" 12x ø13mm / 0,51"

H ø129mm / 5,08" ø129mm / 5,08" ø345,6mm / 13,60" ø530mm / 20,87"

Max. Stern

thickness

BOLT ON INSTALLATION

2a. Once the place for the installation has been decided, hold the tunnel in place in the horizontal position and

mark the bolt holes. Remove the tunnel and it is then possible to calculate and mark the centre (see Fig. 1).

3a. It is important that the tunnel flange sits flush on the transom. If this is not case, then the fitting area on the

transom will have to be worked to ensure a snug fit.

PS ! Take care with grinders as it is very easy to remove to much fibreglass

At this time, cut out the centre hole and the transom to the same internal diameter as the tunnel flange and

drill the bolt holes. Before actual fitting the stern tunnel, we recommend that the prepared area is sealed with

a gelcoat or similar to ensure there is no water ingress.

4a.

Before fitting the tunnel to the transom, install the gear leg to the tunnel as described in the thruster installation

manual. We recommend that you fit the oil feed pipe also before the tunnel is bolted to the transom.

Special installation points described on page 7 of this manual.

5a. When fitting the tunnel, ensure that there is ample sealant (Sikaflex or similar) in the sealing tracks of the

tunnel flange and around the bolts to make a water tight fitting (see FIG. 2&3).

Bolts, washers and nuts are not included as they will vary depending on the transom thickness. We

recommend A4 stainless with A4 lock nuts and A4 washers of a large diameter on both outside and inside.

Bolts diameter (stainless steel):

ø 6mm or 1/4” for SP 30 Si & SP 40 Si

ø 10mm or 3/8” for SP 55 Si & SP 75 Ti & SP 95 Ti & SP 125Ti & SP 155 TCi

ø 12mm or 1/2” for SP200TCi & SP 240 TCi & SP 285 TCi

6a. The electromotor must have a solid support so that the weight

can not cause a twisting action on the tunnel (see FIG. 4).

7a. Refer to the installation manual for the recommended thruster fitting.

Stern thruster installation manual Version 1.6 - 2005

Motor support

MUST be

installed

FIG. 4

FIG. 3

SEALANT

WASHERS

LOCKNUT

OR DOUBLE

NUTS

FIG. 2

SEALANT

Version 1.7.1 - 2010

ø 6mm or 1/4” for SE40/SE60

ø 10mm or 3/8” for SE60/SE80/SE100/SE120/SE130/SE150/SE170/SE210/SE285

SH100/SH160/SH240/SH300

ø 12mm or 1/2” for SH420/SH550

Before tting the tunnel to the transom, install the gearleg to the tunnel as described in the thruster

installation manual. For thrusters with external oil tank, we recommend that the oil feed pipe is tted

before the tunnel ist bolted to the transom.

1 2 3 4 5 6 7 8 ... 11 12

Komentarze do niniejszej Instrukcji

Brak uwag

Side-Power SX80/185T Instrukcja Instalacji Strona 3

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Nie Side-Power SX80/185T